Netgear Nighthawk AX5400 Setup and Login: A 101 Guide
Nighthawk AX5400 is one of the most incredible products by Netgear. If you have got your hands on the same and want to set it up, this guide will help you gain enough knowledge about its installation process. So, can we start out Netgear Nighthawk AX5400 setup and login guide?
The Basic Preparation: Netgear AX5400 Setup and Login
During the setup process only, you will be asked to create a login password. Therefore, if we do not mention the separate steps to complete the router login process, do not get confused. They will automatically get covered in the Netgear router setup steps. However, there are some cases where you will have to input the default values of the login credentials while setting up the router. Thus, before you head over to make your router up and running, be sure that you have correct default values of the router’s credentials in hand. For your ease, we have mentioned them as below:
Default login address: routerlogin.net or routerlogin.com (web URLs) and 192.168.1.1 (IP)
Factory-set SSID and password: Check the router’s label for their values
Not only the aforementioned details, but you are also required to ensure that you have an active internet connection for Netgear Nighthawk AX5400 setup. You are also suggested to make sure that the router is placed in the same room as the modem. And, the location of both devices is supposed to be free of WiFi interference-creating factors. After that, you can focus on the following steps for your router’s installation.
How to Set Up Netgear Nighthawk AX5400 Router?
The steps mentioned below are equally applicable irrespective of the fact that you are trying to configure it with a Starlink modem, Spectrum modem, or one that belongs to Xfinity. Here’s what you must do to set up the router. Before you give a shot at them, power down all your devices.
- Using a Cat6 cable, please connect the LAN1 jack of your modem and the AX5400 WAN jack.
- The connection must be finger-tight and should be maintained via a damage-free cable.
- Switch on your modem > switch (if applicable) > Netgear Nighthawk AX5400 router.
- The lights on your AX5400 will start blinking. Wait for them to become stable.
- Switch on the computer now and connect it to the router’s default SSID.
- For the SSID and password value, you must check the user manual or the AX5400 label.
- Load an internet browser now and visit routerlogin.net or routerlogin.com.
- Let the wizard detect the presence of another router.
- The Internet Connection will be detected now and you will be asked to choose the working mode of the router.
- Here comes the password creation window. Be sure that you create a strong admin password. Also, provide answer to some security questions.
- Jump the step that asks you to install the latest firmware version. We recommend you do it later.
- Now, you will be asked to assign a new SSID and password to the router’s WiFi network. Your computer will disconnect from the router.
- Reconnect it via the new SSID and WiFi password and log in to your router using the newly created admin password.
- Keep following the on-screen prompts until you see the BASIC Home screen displaying the Internet Status as connected.
- You will also see the summary of settings like Parental Controls, Firmware Version, Attached Devices, Guest Network, etc.
- Exit the setup wizard and try to log in again to verify that the Netgear Nighthawk AX5400 setup process is completed.
The Final Note
You might find the Netgear Nighthawk AX5400 setup process a rocket science. But, it is not actually. Everything involved in the process is just a game of focus and sequential execution of steps. However, you can use the Netgear router login IP instead of web URL in case the latter fails to load the router’s BASIC page for you. It will serve the same purpose as the router login web address. On the off-chance, you want to opt for an easier path, get the Nighthawk mobile app installed on your smartphone and follow the instructions appearing on it after connecting the phone to the router’s network.